ERROR: out of range (4294967295>=0)

JBarreiro · 2022-05-24 17:02:13

Hello,

I am having an issue and cant generate the setup.h5 model.

Keep getting the error:
-> out of range (4294967295>=0), in file: N:\src\setup\Substance.cpp on line 188, version v3.1.1
-> ... unfortunately BASEMENT is killed!

Last lines of Console Output are:
-> Total number of boundary data: 48
-> writing (1/1) data of type '1' to EdgeData/set
-> writing (48/12) data of type '2' to EdgeData/NumValue
-> Number of BC interpolations: 0
-> writing (1/1) data of type '1' to EdInterp/set
-> WARNING: <EdInterp/KeyPostn> has no contents, nothing is written in the runfile (.h5)
-> WARNING: <EdInterp/InSeries> has no contents, nothing is written in the runfile (.h5)
-> WARNING: <EdInterp/NodeStrg> has no contents, nothing is written in the runfile (.h5)
-> WARNING: <EdInterp/EdgeData> has no contents, nothing is written in the runfile (.h5)
-> Number of edge based data modifications: 0
-> writing (1/1) data of type '1' to EdModDat/set
-> WARNING: <EdModDat/ModfInfo> has no contents, nothing is written in the runfile (.h5)
-> WARNING: <EdModDat/NodeStrg> has no contents, nothing is written in the runfile (.h5)
-> WARNING: <EdModDat/EdgeData> has no contents, nothing is written in the runfile (.h5)
-> writing (1/1) data of type '2' to Parameters/CFLnumber
-> writing (1/1) data of type '2' to Parameters/DTmax
-> writing (1/1) data of type '2' to Parameters/MinWaterDepth
-> writing (1/1) data of type '2' to Parameters/Gravity
-> writing (1/1) data of type '1' to Parameters/FrictionOn
-> writing (1/1) data of type '1' to Parameters/FrictionType
-> writing (1/1) data of type '2' to Parameters/MorphStart
-> writing (1/1) data of type '2' to Parameters/FluidDensity
-> writing (1/1) data of type '1' to Parameters/SafeMode
-> writing (10433/3) data of type '1' to CellsAll/EdgeSign

10433 is the total of mesh elements...

Can someone help, asap?
Many thanks!

Last edited by JBarreiro (2022-05-24 17:07:00)

NumericalSam · 2022-05-24 17:08:32

Hi Joao
I recently added some clarification on that issue, please check out this thread: https://forum.basement.ethz.ch/viewtopic.php?id=5438

Best, Sam

JBarreiro · 2022-05-24 17:33:57

Hi Sam,

Thanks. I will check if those issues apply!

Regards

JBarreiro · 2022-05-24 18:19:05

NumericalSam wrote:

Hi Joao
I recently added some clarification on that issue, please check out this thread: https://forum.basement.ethz.ch/viewtopic.php?id=5438
Best, Sam

I think my error is like this one: https://forum.basement.ethz.ch/viewtopi … 6629#p6629

I checked for your suggestions regarding material ID, breaklines/stringdefs and found no issues...

User Forum of Software BASEMENT

#1 2022-05-24 17:02:13

ERROR: out of range (4294967295>=0)

#2 2022-05-24 17:08:32

Re: ERROR: out of range (4294967295>=0)

#3 2022-05-24 17:33:57

Re: ERROR: out of range (4294967295>=0)

#4 2022-05-24 18:19:05

Re: ERROR: out of range (4294967295>=0)

Board footer